Single tank water softener valve AUTOTROL 255/740 Logix 1" electronic (Reg. Time) from 8 to 80 lt.

//www.sinergroup.net/EN/Water+softeners/Residential+single+tank+water+softeners/Single+tank+water+softener+valve+AUTOTROL+255%2F740+Logix+1%22+electronic+%7E28Reg.+Time%7E29+from+8+to+80+lt.+resin/15000207-p.htm

Automatic water softener. Electronic AUTOTROL valve 255/740 Logix 1" (Reg. Time). Valve body made of Noryl plastic material, NSF listed. Programming is simple and fast, just enter the time, day of week, time of regeneration, typically 02.00 at night. Complete with plug adapter 12/230V - 50Hz European plug.
Hardness regulator output. Clutching the set screw is going to open the clapper by-pass, which allow you to mix raw water with water treated by device. At the first turn of the screw, the water hardness output increases. Is required output minimum hardness of around 15°F, but the most commonly used setting is not less than 5°F. Loosening setting screw will allow the clapper by-pass to close. The closing action will reduce mixing with raw water output. To mix a specific output hardness value, adjust screw and test water. Repeat the procedure until you reach the desired hardness value. To check input/output hardness from the device, we recommend to buy cod. 13000001 Titrant kit total hardness (1°F) 15cc single reagent.

TO BUY WITH EVERY SOFTENER
1X 02001014 3-pieces standard housing 10" clear IN-OUT 1" with wrench & wall mounting bracket.
2X 04001006-05 Ionicore wound polypropylene cartridge 9-3/4'' - 50 micron (50)
1X Kit 13000001 Titrant total hardness (1 ° F) 15cc single reagent.

* Water softeners are supplied without salt, we recommend to use pads salt.
* The pressure tanks are supplied filled up to version "40lit."

A bypass valve system must be installed on all systems. The bypass valves isolate the device from the water system and allow the use of untreated water. Routine maintenance or service may also require that the system is put in bypass.

Benefits and advantages
Reduction of water hardness, which is cause of scale. ENERGY SAVING: the device prevents the formation of deposits in pipes and hydraulic lines. Greater sense of wellness during the shower. Skin soft and clean. Increased duration of appliances and boilers. COST SAVING: reduction in the use of soaps, fabric softeners and chemicals. Reduced maintenance costs. Fully automatic operation. It should just worry about adding salt in the water softner.

Increased sodium (for drinking water)
Most of the sodium consumed is taken with foods, especially ones obtained with industrial processing. Salt is a great preservative and therefore is used as an additive for processed products. The assumption of sodium with the water we drink is relatively low compared to that which is taken with food. All softeners to produce softened water through ion exchange resins in, produce softened water output sodium ions. The recommended sodium limit for water intended for human consumption is 200ppm liter. Depending on the concentration of sodium and water hardness, it is possible that the water presents a sodium concentration of higher than recommended. Where this is the case or if you need to follow a low salt content, it is advisable to install a reverse osmosis home for water to drink.

Features
* Min. pressure : 1.38 bar (1.38 kg/cm2)
* Max. pressure : 8.27 bar (8.27 kg/cm2)
* Minimum temperature: 2°C
* Maximum temperature: 38°C
* Input / Output water 1" female thread
* Exhaust: hose connector with 2m. of tube
* Overflow: hose connection 3/8"

Model Specifications 15000207-08 8lt. resin. (for 1/2 people)
* Exchange capacity: 44ºHFxm3.
* Salt consumption for regeneration: 1.24 Kg. / Salt.
* Water consumption for regeneration: 53,6lt.
* Max. flow 0.32 m3/h

Model Specifications 15000207-12 12lt. resin (for 2/3 people)
* Exchange capacity: 66ºHFxm3.
* Salt consumption for regeneration: 1,8 Kg./salt.
* Water consumption for regeneration: 80,4lt.
* Max. flow: 0,54m3/h

Model Specifications 15000207-15 15lt. resin. (for 3/4 people)
* Exchange capacity: 90ºHFxm3.
* Salt consumption for regeneration: 2,5 Kg./salt.
* Water consumption for regeneration: 100,5lt.
* Max. flow 0,68m3/h

Model Specifications 15000207-20 20lt. resin. ( for 4/6 People)
* Exchange capacity: 110ºHFxm3.
* Salt consumption for regeneration: 3,2 Kg./salt.
* Water consumption for regeneration: 134lt.
* Max. flow 0,942m3/h

Model Specifications 15000207-25 25lt. resin. (for 6/8 People)
* Exchange capacity: 137ºHFxm3.
* Salt consumption for regeneration: 3,9 Kg./salt.
* Water consumption for regeneration: 167,5lt.
* Max. flow 0,942m3/h

Model Specifications 15000207-30 30lt. resin. (for 6/8/10 People)
* Exchange capacity: 160ºHFxm3.
* Salt consumption for regeneration: 4,3 Kg./salt.
* Water consumption for regeneration: 201lt.
* Max. flow 1,47m3/h

Model Specifications 15000207-35 35lt. resin.
* Exchange capacity: 175ºHFxm3.
* Salt consumption for regeneration: 5,2 Kg./salt.
* Water consumption for regeneration: 210lt.
* Max. flow 1,56m3/h

Model Specifications 15000207-40 40lt. resin.
* Exchange capacity: 200ºHFxm3.
* Salt consumption for regeneration: 5,9 Kg./salt.
* Water consumption for regeneration: 240lt.
* Max. flow 1,56m3/h

Model Specifications 15000207-50 50lt. resin.
* Exchange capacity: 250ºHFxm3.
* Salt consumption for regeneration: 7,3 Kg./salt.
* Water consumption for regeneration: 262lt.
* Max. flow 1,56m3/h
* The pressure tanks are supplied filled up to version "40lit."

Model Specifications 15000207-60 60lt. resin.
* Exchange capacity: 300ºHFxm3.
* Salt consumption for regeneration: 9,1 Kg./salt.
* Water consumption for regeneration: 360lt.
* Max. flow 2,21m3/h
* The pressure tanks are supplied filled up to version "40lit."

Model Specifications 15000207-70 70lt. resin.
* Exchange capacity: 350ºHFxm3.
* Salt consumption for regeneration: 11,3 Kg./salt.
* Water consumption for regeneration: 511lt.
* Max. flow 2,63m3/h
* The pressure tanks are supplied filled up to version "40lit."

Model Specifications 15000207-75 75lt. resin.
* Exchange capacity: 375ºHFxm3.
* Salt consumption for regeneration: 15 Kg./salt.
* Water consumption for regeneration: 538lt.
* Max. flow 2,63m3/h
* The pressure tanks are supplied filled up to version "40lit."

Model Specifications 15000207-80 80lt. resin.
* Exchange capacity: 400ºHFxm3.
* Salt consumption for regeneration: 15 Kg./salt.
* Water consumption for regeneration: 538lt.
* Max. flow 2,63m3/h
* The pressure tanks are supplied filled up to version "40lit."

* We provide only businesses companies such as distributors, retailers, manufacturers and assemblers.